Go daddy RU 728x90 hosting

Linux distro ham radio

linux distro ham radio

What am I doing wrong. My rtl Sdr 2838 works fine on my Android tablet. 34ghz processor and Windows 8. I had no luck. Tried downloading all drives and software so I can operate it on my Acer aspire x desktop with 2. And looked in devices and rtl sdr driver isn’t installed. Keeps saying no device found.

Because the vast majority of PC users had to learn Windows for various reasons (work, for a long time PCs came only with Windows, etc) and very few PC users had/have to learn Linux, the perception arose that Windows MUST BE easier. That’s like saying that Mandarin is easier to learn than English or Spanish because more people speak it than English and Spanish combined. There is a misperception in the Windows vs Linux debate. After all, if it wasn’t easier, there would not be so many Windows users.

I am having some trouble with my set up. I have also tried using different sample rates and gains. I have tried two different SDR radios and i have also ran it on a raspberry Pi B and the new raspberry Pi 2 B+, while also using a usb hub. The problem is that after say 5 mins of running the server successfully the SdrSharp either crashes or starts to lag, and even the signal becomes highly distorted and i get large peak all over the full spectrum on all frequencies.

Hi, I did run into the same error messages on my Pi and my solution was to “wirebridge” the SMD fuses on the board at the output USB ports. At a current of 200 mAmps they have a drop of about 300 mV which makes the power voltage to low for the dongles.

linux distro ham radio

The new ‘Firmware’ includes DVB drivers and subsequently takes over the DVB stick, causing this server to fail. I know a bit about Linux, but not quite enough yet to remove the new unwanted drivers – any suggestions welcome. I presume this would be the case with any future (post 25/9/13 Raspian image) install as well. Luckily I had a backup image which has got my setup working again, but I think a solution is needed to block the DVB drivers in the new ‘Firmware’. Great project, and I’ve been using this for the last 9 months with no problems, but I just made the mistake of updating the ‘Firmware’ on the Raspberry Pi.

000+ links organized into 600+ categories and subcategories. About The DXZone The DXZone is the largest human created and maintained library of web sites dedicated to Amateur Radio, currently lists 20. Ham Radio operators review new sites every day since 1998, for potential inclusion in the Directory, and to evaluate the best place to list them.

Feb 03, 2014 · December 2013’s EOF, titled “Mars Needs Women”, visited an interesting fact: that the male/female ratio among Linux Journal readers, and Linux kernel.

K2ZA - Explorations in Amateur Radio: July 2016

But as it is: mine-ubuntu mate, wife’s- Linux mint, daughters(6yold) Ubuntu + edubuntu package, work- Ubuntu mate(to be changed soon for more network management oriented stuff)
Not forgetting that all below uses some flavour of *nix, too: Sam**ng smart TV, sky sat receiver, NAS unit, sonos player.

I checked it out using another HF rig with the new CH3 and is was right on frequency. Was able to change 60m Channel 3 to the new frequency yesterday. The only two problem I had was that I had to disconnect all other USB devices and force the CT-62 cable to use COM3 because CHIRP would not list COM16, which Vista initially assigned it. The other problem was a cockpit error, I selected FT-817 instead of FT-817ND and that caused a checksum error. Used Windows Vista and the CT-62 USB cable with the Prolific chipset. Other than that, follow the above precedure and it will work for you too. Thanks for the program and procedure.

” I find the “even 5 choices are too may” to be a specious argument. Users who want to try Linux are little advanced past “average. Most distros are available as LiveCDs, something that cannot be said about Windows. “2) Even 10 choices is too many. Users who say that do not have the same problem when choosing between all the office suites offered for Windows. It’s not like they will have to pay an exorbitant licensing fee for each distro. They don’t even have to install the distro to their hard drive. An “average mainstream Windows user” will not be interested in switching operating systems. They try one, don’t like, go on to the next one. )”
I believe there is a misconception here. So why is it so hard to choose a distro. (Remember, I’m talking about average mainstream users. It’s not like they will be forced to use a particular distro exclusively until the end of time. They do not have the same problem when choosing between all the media players for Windows. Even 5 choices is too many. As far as (s)he is concerned Windows is THE one and only O/S in existence.

This is one area where it has a lot of room left for improvement, though. Hey Jean-Francois, you’re absolutely right. There was a small disclaimer at the start of the article that said what you said: Linux in a non-desktop context is pretty much conquering the world.

I dont need to install my Line 6 Guitar box. Hardware on Linux seems to work easier for me. I dont have to install camera drivers from Logitech. It worked with Guitarix. I did not need to install my printer, scanner, and have found great success using Openshot for video edits.


Leave a Reply

Your email address will not be published. Required fields are marked *